6GB Corsair Dominator-GT 2000MHz DDR3 Memory E-mail
Reviews - Featured Reviews: Memory
Written by Olin Coles   
Wednesday, 07 April 2010
Table of Contents: Page Index
6GB Corsair Dominator-GT 2000MHz DDR3 Memory
Closer Look: Corsair Dominator-GT DDR3
DDR3 Series Results
RAM Testing Methodology
System Benchmark Tests
Graphics Benchmark Tests
Triple-Channel DDR3 Final Thoughts
Corsair Dominator-GT DDR3 Conclusion

Introduction to DDR3

This section offers a very brief overview of DDR3 technology, however Benchmark Reviews also offers the comprehensive article: DDR3 RAM - System Memory Technology Explained. The new generation of DDR3 is meant to avoid a bottleneck between the CPU and the system memory; especially in highly overclocked scenarios. With the high-speed variety of DDR3, which presently includes everything beyond the highest 1600MHz JEDEC standard, you increase the Front Side Bus (FSB) and CPU clock speed without being forced to slow the system memory to remain stable. Here are a the primary benefits of DDR3 SDRAM:


  • Now supports a system level flight time compensation
  • Mirror-friendly DRAM pin out are now contained on-DIMM
  • CAS Write latency are now issued to each speed bin
  • Asynchronous reset function is available for the first time in SDRAM
  • I/O calibration engine monitors flight time and correction levels
  • Automatic data bus line read and write calibration


  • Higher bandwidth performance increase, up to 1600 MHz per spec
  • DIMM-terminated 'fly-by' command bus
  • Constructed with high-precision load line calibration resistors
  • Performance increase at low power input
  • Enhanced low power features conserve energy
  • Improved thermal design now operates DIMM cooler

Each generation of DDR is more than just an update to the memory speed, it is also a more technologically advanced production process and a lower operating voltage and better heat dissipation. The previous generation of DDR2 is manufactured on a 110nm node, whereas the new DDR3 has receives a fab process shrink down to a 90nm node (although some use 80nm) with either 55/45nm prepared for later into 2008. Together, this all helps the hardware enthusiast reach higher clock speeds at the expense of higher latencies. This is why the new DDR3 generation of memory needs a significantly higher clock speed deliver better performance than the preceding generation of DDR2 technology.

In additional to the logically progressive changes, there are also improvements made to the architectural design of the memory. One particularly important change introduced with DDR3 is in the prefetch buffer: up from DDR2's four bits to an astounding eight bits per cycle. This translates to a full 100% increase in the prefetch payload; not just a small incremental improvement as there have been in the other area's.

DDR2-400 Memory is equal in performance to DDR-400, which is why it must operate at DDR2-667 speed to carry incentive. The same scenario is generally true with DDR3 when compared to DDR2. While in theory DDR2-1066 offers the same performance as DDR3-1066, this generally means that DDR3 requires a DDR3-1333 speed to show any benefit over DDR2-800. Memories within the same generation (DDR/DDR2/DDR3) are downwards compatible, meaning that if you have DDR3-1600 RAM, you can configure it to operate at 1066 and 1333 MHz speeds.



# 6 DIMMs on P55?Hsew 2010-04-07 18:49
"Many dual-channel P55-Express motherboards offer six DIMM slots."

I'm sorry, but the only one that comes to mind is the Gigabyte GA-P55(A)-UD6 which, ironically, is STILL limited to 16GB, which means one must either install 4x4 GB or 4x2 and 2x4 GB to satisfy the limit. What is the point of that board anyway?
Report Comment
# RE: 6GB Corsair Dominator-GT 2000MHz DDR3 MemoryDavid Ramsey 2010-04-08 12:52
The point of that board is to allow you to make use of any single-sided DIMMs you have laying around. It wouldn't make sense if you were buying all-new memory for a new build.
Report Comment
# HeightSVH 2010-04-14 12:11
Seems the height of these modules would interfere with many of the higher capacity coolers on the market esp. when all 6 slots are used. What cooler did you use in this test? Would it have interfered if all 6 slots were filled. I am interested because I have the same mainboard and memory but need a higher end cpu cooler.

Report Comment
# ClearanceOlin Coles 2010-04-14 13:19
I used the ProlimaTech Megahalems on the ASUS P6X58D motherboard. The cooler was situated so that the fan blows towards the back of the case. Although the cooler would perform better if it was situated so the fan would blow towards the top, it would interfere with the DIMM slots.
Report Comment

Comments have been disabled by the administrator.

Search Benchmark Reviews

Like Benchmark Reviews on FacebookFollow Benchmark Reviews on Twitter