Archive Home arrow Reviews: arrow Memory arrow OCZ Reaper HPC PC2-9200 DDR2 1150MHz RAM Kit








OCZ Reaper HPC PC2-9200 DDR2 1150MHz RAM Kit E-mail
Reviews - Featured Reviews: Memory
Written by Olin Coles   
Saturday, 13 October 2007
Table of Contents: Page Index
OCZ Reaper HPC PC2-9200 DDR2 1150MHz RAM Kit
Closer Look: OCZ Reaper HPC
RAM Testing Methodology
Test Results
Final Thoughts and Conclusion

Testing Methodology: DDR2 RAM

Before the testing really begins, there are several settings we adjust in the BIOS. Many combinations of the CPU's front side bus are matched to a specific memory multiplier, giving us the desired RAM (and CPU) operating speed. This is important because I have learned that a module set to 3.33 multiplier with a 344MHz FSB will fail every test, but that same module set to a 3.2 multiplier with 357MHz FSB will run stable all day. When we begin this process and begin benchmarking for a baseline reading, the memory voltage and clock speed is always left at the manufacturer's default values. However, later into the testing I may (rarely) decide to raise the voltage if it looks like it will allow me to reach higher overclocked speeds.

After each and every change to the BIOS, the system is restarted and all RAM modules are automatically tested with MemTest86+ for one full pass. Since the modules are not overclocked, one pass is usually sufficient to determine if a bad part exists. Later, once I begin to overclock the memory, these tests are a good way of quickly pre-screening stable configurations. Once the test pass is complete, I move onto the synthetic benchmark tests. Here at Benchmark Reviews we use the following test suites and applications:

  • SiSoft Sandra Lite v2008.1.12.34
  • Lavalys EVEREST v4.00.976
  • Passmark Performance Test v6.01.1001
  • World in Conflict v1.0.0.1 (Build 81)

After all of the tests have been performed at the default memory clock speeds, which establishes the baseline reading for our comparisons, I then increase the front side bus to overclock the RAM without adding any additional voltage. My theory is this: a module that will overclock without additional voltage is going to perform better than a module which requires you to potentially damage it or void the warranty. I am fully aware that many sites turn up the voltage and apply dangerous amounts of power to the modules so that they can unlock that last megahertz; but if I begin down that road where will it end? Do I then start writing reviews where I apply liquid nitrogen cooling to the RAM? Do I volt-mod the motherboard and apply so much power I ruin expensive parts and equipment? In the end, I decided that overclocking will be done at the stock voltage for benchmarks, because I believe most enthusiasts are going to aim for the same goal. If at some point I feel like adding voltage would potentially return performance gains, then I will add up to 0.2V to the default volt rating.

OCZ Reaper HPC PC2-9200 DDR2 1150MHz RAM Kit OCZ2RPR11502GK

In each synthetic benchmark test Windows XP was booted fresh and the application was opened. Task manager was then utilized to end the explorer.exe (Windows) process so that only the most essential services were running and a trim 16 processes total were consuming system memory. This procedure allowed the RAM to be as isolated as possible for our testing.

Test System

OCZ Reaper HPC PC2-9200 DDR2 1150MHz RAM Kit OCZ2RPR11502GK

Test Products:

  • OCZ PC2-9200 CL 5-5-5-18 Reaper HPC OCZ2RPR11502GK DDR2 1150MHz RAM Kit (Featured Product)

Sometimes it is very difficult to get broad results between the memory modules tested, so we use several different speeds of memory from participating manufacturers. Benchmark Reviews is very serious about performance, which is why we test the products against as many benchmarks as reasonably possible. Not every test suite is effective in these reviews, and some often calculate processor and other system components into the score. This is what makes a RAM review difficult: unless all of the modules compared have the exact same rating and the CPU operates at the exact same speed for each and every test, the comparison is always going to be subjective.



 

Comments have been disabled by the administrator.

Search Benchmark Reviews

Like Benchmark Reviews on FacebookFollow Benchmark Reviews on Twitter